in the "refactor tcpquota and pipeline refs" commit, the counting
of active interfaces was tightened in such a way that named could
fail to listen on an interface if there were more interfaces than
tcp-clients. when checking the quota to start accepting on an
interface, if the number of active clients was above zero, then
it was presumed that some other client was able to handle accepting
new connections. this, however, ignored the fact that the current client
could be included in that count, so if the quota was already exceeded
before all the interfaces were listening, some interfaces would never
listen.
we now check whether the current client has been marked active; if so,
then the number of active clients on the interface must be greater
than 1, not 0.
(cherry picked from commit 0b4e2cd4c3192ba88569dd344f542a8cc43742b5)
- if the TCP quota has been exceeded but there are no clients listening
for new connections on the interface, we can now force attachment to the
quota using isc_quota_force(), instead of carrying on with the quota not
attached.
- the TCP client quota is now referenced via a reference-counted
'ns_tcpconn' object, one of which is created whenever a client begins
listening for new connections, and attached to by members of that
client's pipeline group. when the last reference to the tcpconn
object is detached, it is freed and the TCP quota slot is released.
- reduce code duplication by adding mark_tcp_active() function.
- convert counters to atomic.
(cherry picked from commit 7e8222378ca24f1302a0c1c638565050ab04681b)
(cherry picked from commit 4939451275722bfda490ea86ca13e84f6bc71e46)
- ensure that tcpactive is cleaned up correctly when accept() fails.
- set 'client->tcpattached' when the client is attached to the tcpquota.
carry this value on to new clients sharing the same pipeline group.
don't call isc_quota_detach() on the tcpquota unless tcpattached is
set. this way clients that were allowed to accept TCP connections
despite being over quota (and therefore, were never attached to the
quota) will not inadvertently detach from it and mess up the
accounting.
- simplify the code for tcpquota disconnection by using a new function
tcpquota_disconnect().
- before deciding whether to reject a new connection due to quota
exhaustion, check to see whether there are at least two active
clients. previously, this was "at least one", but that could be
insufficient if there was one other client in READING state (waiting
for messages on an open connection) but none in READY (listening
for new connections).
- before deciding whether a TCP client object can to go inactive, we
must ensure there are enough other clients to maintain service
afterward -- both accepting new connections and reading/processing new
queries. A TCP client can't shut down unless at least one
client is accepting new connections and (in the case of pipelined
clients) at least one additional client is waiting to read.
(cherry picked from commit c7394738b2445c16f728a88394864dd61baad900)
(cherry picked from commit e965d5f11d3d0f6d59704e614fceca2093cb1856)
the TCP client quota could still be ineffective under some
circumstances. this change:
- improves quota accounting to ensure that TCP clients are
properly limited, while still guaranteeing that at least one client
is always available to serve TCP connections on each interface.
- uses more descriptive names and removes one (ntcptarget) that
was no longer needed
- adds comments
(cherry picked from commit 924651f1d5e605cd186d03f4f7340bcc54d77cc2)
tcp-clients settings could be exceeded in some cases by
creating more and more active TCP clients that are over
the set quota limit, which in the end could lead to a
DoS attack by e.g. exhaustion of file descriptors.
If TCP client we're closing went over the quota (so it's
not attached to a quota) mark it as mortal - so that it
will be destroyed and not set up to listen for new
connections - unless it's the last client for a specific
interface.
(cherry picked from commit f97131d21b97381cef72b971b157345c1f9b4115)
If in keyfetch_done the compute_tag fails (because for example the
algorithm is not supported), don't crash, but instead ignore the
key.
(cherry picked from commit b1d5411569ae10830b63f07560091193646cc739)
These tests check if a key with an unsupported algorithm in
managed-keys is ignored and when seeing an algorithm rollover to
an unsupported algorithm, the new key will be ignored too.
(cherry picked from commit 144cb53d0ae3aa5e6e3123720b603f9ab2bd1fa9)
If `dns_dnssec_keyfromrdata` failed we don't need to call
`dst_key_free` because no `dstkey` was created. Doing so
nevertheless will result in an assertion failure.
This can happen if the key uses an unsupported algorithm.
(cherry picked from commit 7a1ca39b950b7d5230b605ac60f15a1cb94e3d69)
- dig command had the @ parameter in the wrong place
- private-dnskey and private-cdnskey are queried in a separate
loop, which strips 'private-' from the name to determine the qtype
(cherry picked from commit bc7b34d6ef)