ComputerSurge/bind9
3
0
Fork 0
Code Pull Requests 1 Activity
Files
8786484edfafa016454a4cfcdcab6284aeff52cb
bind9/doc/draft/draft-ietf-ipngwg-rfc2553bis-03.txt
Andreas Gustafsson 54dc3afd27 added IPv6 API drafts
2001-04-27 17:55:01 +00:00

2045 lines
74 KiB
Plaintext
Raw Blame History

IPNG Working Group R.E. Gilligan
INTERNET-DRAFT: draft-ietf-ipngwg-rfc2553bis-03.txt Cache Flow
Obsoletes RFC 2553 S. Thomson
Cisco
J. Bound
Nokia Networks
W. R. Stevens
February 2001
Basic Socket Interface Extensions for IPv6
<draft-ietf-ipngwg-rfc2553bis-03.txt>
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026.
This document is a submission by the Internet Protocol IPv6 Working
Group of the Internet Engineering Task Force (IETF). Comments should
be submitted to the ipng@sunroof.eng.sun.com mailing list.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet- Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Abstract
The de facto standard application program interface (API) for TCP/IP
applications is the "sockets" interface. Although this API was
developed for Unix in the early 1980s it has also been implemented on a
wide variety of non-Unix systems. TCP/IP applications written using the
sockets API have in the past enjoyed a high degree of portability and we
would like the same portability with IPv6 applications. But changes are
required to the sockets API to support IPv6 and this memo describes
these changes. These include a new socket address structure to carry
IPv6 addresses, new address conversion functions, and some new socket
options. These extensions are designed to provide access to the basic
IPv6 features required by TCP and UDP applications, including
multicasting, while introducing a minimum of change into the system and
providing complete compatibility for existing IPv4 applications.
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 1]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
Additional extensions for advanced IPv6 features (raw sockets and access
to the IPv6 extension headers) are defined in another document [4].
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 2]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
Table of Contents:
1. Introduction.................................................4
2. Design Considerations........................................4
2.1 What Needs to be Changed....................................4
2.2 Data Types..................................................6
2.3 Headers.....................................................6
2.4 Structures..................................................6
3. Socket Interface.............................................6
3.1 IPv6 Address Family and Protocol Family.....................6
3.2 IPv6 Address Structure......................................6
3.3 Socket Address Structure for 4.3BSD-Based Systems...........7
3.4 Socket Address Structure for 4.4BSD-Based Systems...........8
3.5 The Socket Functions........................................9
3.6 Compatibility with IPv4 Applications.......................10
3.7 Compatibility with IPv4 Nodes..............................10
3.8 IPv6 Wildcard Address......................................10
3.9 IPv6 Loopback Address......................................11
3.10 Portability Additions.....................................12
4. Interface Identification....................................14
4.1 Name-to-Index..............................................14
4.2 Index-to-Name..............................................15
4.3 Return All Interface Names and Indexes.....................15
4.4 Free Memory................................................15
5. Socket Options..............................................16
5.1 Unicast Hop Limit..........................................16
5.2 Sending and Receiving Multicast Packets....................17
5.3 IPV6_V6ONLY option for AF_INET6 Sockets....................18
6. Library Functions...........................................19
6.1 Protocol-Independent Nodename and Service Name Translation.19
6.2 Socket Address Structure to Nodename and Service Name......23
6.3 Address Conversion Functions...............................25
6.4 Address Testing Macros.....................................26
7. Summary of New Definitions..................................27
8. Security Considerations.....................................28
9. Year 2000 Considerations....................................28
Changes made to rfc2553bis-02 to rfc2553bis-03.................29
Changes made to rfc2553bis-01 to rfc2553bis-02.................29
Changes made to rfc2553bis-00 to rfc2553bis-01.................29
Changes made rfc2553 to rfc2553bis-00:.........................29
Acknowledgments................................................30
References.....................................................30
Authors' Addresses.............................................31
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 3]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
1. Introduction
While IPv4 addresses are 32 bits long, IPv6 interfaces are identified by
128-bit addresses. The socket interface makes the size of an IP address
quite visible to an application; virtually all TCP/IP applications for
BSD-based systems have knowledge of the size of an IP address. Those
parts of the API that expose the addresses must be changed to
accommodate the larger IPv6 address size. IPv6 also introduces new
features (e.g., traffic class and flowlabel), some of which must be made
visible to applications via the API. This memo defines a set of
extensions to the socket interface to support the larger address size
and new features of IPv6.
2. Design Considerations
There are a number of important considerations in designing changes to
this well-worn API:
- The API changes should provide both source and binary
compatibility for programs written to the original API. That
is, existing program binaries should continue to operate when
run on a system supporting the new API. In addition, existing
applications that are re-compiled and run on a system supporting
the new API should continue to operate. Simply put, the API
changes for IPv6 should not break existing programs. An additional
mechanism for implementations to verify this is to verify the new
symbols are protected by Feature Test Macros as described in IEEE Std
1003.1-200x. (Such Feature Test Macros are not defined by this RFC.)
- The changes to the API should be as small as possible in order
to simplify the task of converting existing IPv4 applications to
IPv6.
- Where possible, applications should be able to use this
API to interoperate with both IPv6 and IPv4 hosts. Applications
should not need to know which type of host they are
communicating with.
- IPv6 addresses carried in data structures should be 64-bit
aligned. This is necessary in order to obtain optimum
performance on 64-bit machine architectures.
Because of the importance of providing IPv4 compatibility in the API,
these extensions are explicitly designed to operate on machines that
provide complete support for both IPv4 and IPv6. A subset of this API
could probably be designed for operation on systems that support only
IPv6. However, this is not addressed in this memo.
2.1 What Needs to be Changed
The socket interface API consists of a few distinct components:
- Core socket functions.
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 4]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
- Address data structures.
- Name-to-address translation functions.
- Address conversion functions.
The core socket functions -- those functions that deal with such things
as setting up and tearing down TCP connections, and sending and
receiving UDP packets -- were designed to be transport independent.
Where protocol addresses are passed as function arguments, they are
carried via opaque pointers. A protocol-specific address data structure
is defined for each protocol that the socket functions support.
Applications must cast pointers to these protocol-specific address
structures into pointers to the generic "sockaddr" address structure
when using the socket functions. These functions need not change for
IPv6, but a new IPv6-specific address data structure is needed.
The "sockaddr_in" structure is the protocol-specific data structure for
IPv4. This data structure actually includes 8-octets of unused space,
and it is tempting to try to use this space to adapt the sockaddr_in
structure to IPv6. Unfortunately, the sockaddr_in structure is not
large enough to hold the 16-octet IPv6 address as well as the other
information (address family and port number) that is needed. So a new
address data structure must be defined for IPv6.
IPv6 addresses are scoped [2] so they could be link-local, site,
organization, global, or other scopes at this time undefined. To
support applications that want to be able to identify a set of
interfaces for a specific scope, the IPv6 sockaddr_in structure must
support a field that can be used by an implementation to identify a set
of interfaces identifying the scope for an IPv6 address.
The name-to-address translation functions in the socket interface are
gethostbyname() and gethostbyaddr(). These are left as is and new
functions are defined to support IPv4 and IPv6. The new API is based on
the IEEE Std 1003.1-200x draft [3] and specifies a new nodename-to-
address translation function which is protocol independent. This
function can also be used with IPv4 and IPv6.
The address conversion functions -- inet_ntoa() and inet_addr() --
convert IPv4 addresses between binary and printable form. These
functions are quite specific to 32-bit IPv4 addresses. We have designed
two analogous functions that convert both IPv4 and IPv6 addresses, and
carry an address type parameter so that they can be extended to other
protocol families as well.
Finally, a few miscellaneous features are needed to support IPv6. New
interfaces are needed to support the IPv6 traffic class, flow label, and
hop limit header fields. New socket options are needed to control the
sending and receiving of IPv6 multicast packets.
The socket interface will be enhanced in the future to provide access to
other IPv6 features. These extensions are described in [4].
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 5]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
2.2 Data Types
The data types of the structure elements given in this memo are intended
to track the relevant standards. uintN_t means an unsigned integer of
exactly N bits (e.g., uint16_t).
2.3 Headers
When function prototypes and structures are shown we show the headers
that must be #included to cause that item to be defined.
2.4 Structures
When structures are described the members shown are the ones that must
appear in an implementation. Additional, nonstandard members may also
be defined by an implementation. As an additional precaution
nonstandard members could be verified by Feature Test Macros as
described in IEEE Std 1003.1-200x. (Such Feature Test Macros are not
defined by this RFC.)
The ordering shown for the members of a structure is the recommended
ordering, given alignment considerations of multibyte members, but an
implementation may order the members differently.
3. Socket Interface
This section specifies the socket interface changes for IPv6.
3.1 IPv6 Address Family and Protocol Family
A new address family name, AF_INET6, is defined in <sys/socket.h>. The
AF_INET6 definition distinguishes between the original sockaddr_in
address data structure, and the new sockaddr_in6 data structure.
A new protocol family name, PF_INET6, is defined in <sys/socket.h>.
Like most of the other protocol family names, this will usually be
defined to have the same value as the corresponding address family name:
#define PF_INET6 AF_INET6
The PF_INET6 is used in the first argument to the socket() function to
indicate that an IPv6 socket is being created.
3.2 IPv6 Address Structure
A new in6_addr structure holds a single IPv6 address and is defined as a
result of including <netinet/in.h>:
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 6]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
struct in6_addr {
uint8_t s6_addr[16]; /* IPv6 address */
};
This data structure contains an array of sixteen 8-bit elements, which
make up one 128-bit IPv6 address. The IPv6 address is stored in network
byte order.
The structure in6_addr above is usually implemented with an embedded
union with extra fields that force the desired alignment level in a
manner similar to BSD implementations of "struct in_addr". Those
additional implementation details are omitted here for simplicity.
An example is as follows:
struct in6_addr {
union {
uint8_t _S6_u8[16];
uint32_t _S6_u32[4];
uint64_t _S6_u64[2];
} _S6_un;
};
#define s6_addr _S6_un._S6_u8
3.3 Socket Address Structure for 4.3BSD-Based Systems
In the socket interface, a different protocol-specific data structure is
defined to carry the addresses for each protocol suite. Each protocol-
specific data structure is designed so it can be cast into a protocol-
independent data structure -- the "sockaddr" structure. Each has a
"family" field that overlays the "sa_family" of the sockaddr data
structure. This field identifies the type of the data structure.
The sockaddr_in structure is the protocol-specific address data
structure for IPv4. It is used to pass addresses between applications
and the system in the socket functions. The following sockaddr_in6
structure holds IPv6 addresses and is defined as a result of including
the <netinet/in.h> header:
struct sockaddr_in6 {
sa_family_t sin6_family; /* AF_INET6 */
in_port_t sin6_port; /* transport layer port # */
uint32_t sin6_flowinfo; /* IPv6 traffic class & flow info */
struct in6_addr sin6_addr; /* IPv6 address */
uint32_t sin6_scope_id; /* set of interfaces for a scope */
};
This structure is designed to be compatible with the sockaddr data
structure used in the 4.3BSD release.
The sin6_family field identifies this as a sockaddr_in6 structure. This
field overlays the sa_family field when the buffer is cast to a sockaddr
data structure. The value of this field must be AF_INET6.
The sin6_port field contains the 16-bit UDP or TCP port number. This
field is used in the same way as the sin_port field of the sockaddr_in
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 7]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
structure. The port number is stored in network byte order.
The sin6_flowinfo field is a 32-bit field that contains two pieces of
information: the traffic class and the flow label. The contents and
interpretation of this member is specified in [1]. The sin6_flowinfo
field SHOULD be set to zero by an implementation prior to using the
sockaddr_in6 structure by an application on receive operations.
The sin6_addr field is a single in6_addr structure (defined in the
previous section). This field holds one 128-bit IPv6 address. The
address is stored in network byte order.
The ordering of elements in this structure is specifically designed so
that when sin6_addr field is aligned on a 64-bit boundary, the start of
the structure will also be aligned on a 64-bit boundary. This is done
for optimum performance on 64-bit architectures.
The sin6_scope_id field is a 32-bit integer that identifies a set of
interfaces as appropriate for the scope of the address carried in the
sin6_addr field [2,5,6,7]. For a link scope sin6_addr, sin6_scope_id
would be an interface index. For a site scope sin6_addr, sin6_scope_id
would be a site identifier. The mapping of sin6_scope_id to an
interface or set of interfaces is left to implementation and future
specifications on the subject of site identifiers.
Notice that the sockaddr_in6 structure will normally be larger than the
generic sockaddr structure. On many existing implementations the
sizeof(struct sockaddr_in) equals sizeof(struct sockaddr), with both
being 16 bytes. Any existing code that makes this assumption needs to
be examined carefully when converting to IPv6.
3.4 Socket Address Structure for 4.4BSD-Based Systems
The 4.4BSD release includes a small, but incompatible change to the
socket interface. The "sa_family" field of the sockaddr data structure
was changed from a 16-bit value to an 8-bit value, and the space saved
used to hold a length field, named "sa_len". The sockaddr_in6 data
structure given in the previous section cannot be correctly cast into
the newer sockaddr data structure. For this reason, the following
alternative IPv6 address data structure is provided to be used on
systems based on 4.4BSD. It is defined as a result of including the
<netinet/in.h> header.
struct sockaddr_in6 {
uint8_t sin6_len; /* length of this struct */
sa_family_t sin6_family; /* AF_INET6 */
in_port_t sin6_port; /* transport layer port # */
uint32_t sin6_flowinfo; /* IPv6 flow information */
struct in6_addr sin6_addr; /* IPv6 address */
uint32_t sin6_scope_id; /* set of interfaces for a scope */
};
The only differences between this data structure and the 4.3BSD variant
are the inclusion of the length field, and the change of the family
field to a 8-bit data type. The definitions of all the other fields are
identical to the structure defined in the previous section.
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 8]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
Systems that provide this version of the sockaddr_in6 data structure
must also declare SIN6_LEN as a result of including the <netinet/in.h>
header. This macro allows applications to determine whether they are
being built on a system that supports the 4.3BSD or 4.4BSD variants of
the data structure.
3.5 The Socket Functions
Applications call the socket() function to create a socket descriptor
that represents a communication endpoint. The arguments to the socket()
function tell the system which protocol to use, and what format address
structure will be used in subsequent functions. For example, to create
an IPv4/TCP socket, applications make the call:
s = socket(PF_INET, SOCK_STREAM, 0);
To create an IPv4/UDP socket, applications make the call:
s = socket(PF_INET, SOCK_DGRAM, 0);
Applications may create IPv6/TCP and IPv6/UDP sockets by simply using
the constant PF_INET6 instead of PF_INET in the first argument. For
example, to create an IPv6/TCP socket, applications make the call:
s = socket(PF_INET6, SOCK_STREAM, 0);
To create an IPv6/UDP socket, applications make the call:
s = socket(PF_INET6, SOCK_DGRAM, 0);
Once the application has created a PF_INET6 socket, it must use the
sockaddr_in6 address structure when passing addresses in to the system.
The functions that the application uses to pass addresses into the
system are:
bind()
connect()
sendmsg()
sendto()
The system will use the sockaddr_in6 address structure to return
addresses to applications that are using PF_INET6 sockets. The
functions that return an address from the system to an application are:
accept()
recvfrom()
recvmsg()
getpeername()
getsockname()
No changes to the syntax of the socket functions are needed to support
IPv6, since all of the "address carrying" functions use an opaque
address pointer, and carry an address length as a function argument.
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 9]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
3.6 Compatibility with IPv4 Applications
In order to support the large base of applications using the original
API, system implementations must provide complete source and binary
compatibility with the original API. This means that systems must
continue to support PF_INET sockets and the sockaddr_in address
structure. Applications must be able to create IPv4/TCP and IPv4/UDP
sockets using the PF_INET constant in the socket() function, as
described in the previous section. Applications should be able to hold
a combination of IPv4/TCP, IPv4/UDP, IPv6/TCP and IPv6/UDP sockets
simultaneously within the same process.
Applications using the original API should continue to operate as they
did on systems supporting only IPv4. That is, they should continue to
interoperate with IPv4 nodes.
3.7 Compatibility with IPv4 Nodes
The API also provides a different type of compatibility: the ability for
IPv6 applications to interoperate with IPv4 applications. This feature
uses the IPv4-mapped IPv6 address format defined in the IPv6 addressing
architecture specification [2]. This address format allows the IPv4
address of an IPv4 node to be represented as an IPv6 address. The IPv4
address is encoded into the low-order 32 bits of the IPv6 address, and
the high-order 96 bits hold the fixed prefix 0:0:0:0:0:FFFF. IPv4-
mapped addresses are written as follows:
::FFFF:<IPv4-address>
These addresses can be generated automatically by the getaddrinfo()
function, when the specified host has only IPv4 addresses (as described
in Section 6.1 and 6.2).
Applications may use PF_INET6 sockets to open TCP connections to IPv4
nodes, or send UDP packets to IPv4 nodes, by simply encoding the
destination's IPv4 address as an IPv4-mapped IPv6 address, and passing
that address, within a sockaddr_in6 structure, in the connect() or
sendto() call. When applications use PF_INET6 sockets to accept TCP
connections from IPv4 nodes, or receive UDP packets from IPv4 nodes, the
system returns the peer's address to the application in the accept(),
recvfrom(), or getpeername() call using a sockaddr_in6 structure encoded
this way.
Few applications will likely need to know which type of node they are
interoperating with. However, for those applications that do need to
know, the IN6_IS_ADDR_V4MAPPED() macro, defined in Section 6.7, is
provided.
3.8 IPv6 Wildcard Address
While the bind() function allows applications to select the source IP
address of UDP packets and TCP connections, applications often want the
system to select the source address for them. With IPv4, one specifies
the address as the symbolic constant INADDR_ANY (called the "wildcard"
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 10]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
address) in the bind() call, or simply omits the bind() entirely.
Since the IPv6 address type is a structure (struct in6_addr), a symbolic
constant can be used to initialize an IPv6 address variable, but cannot
be used in an assignment. Therefore systems provide the IPv6 wildcard
address in two forms.
The first version is a global variable named "in6addr_any" that is an
in6_addr structure. The extern declaration for this variable is defined
in <netinet/in.h>:
extern const struct in6_addr in6addr_any;
Applications use in6addr_any similarly to the way they use INADDR_ANY in
IPv4. For example, to bind a socket to port number 23, but let the
system select the source address, an application could use the following
code:
struct sockaddr_in6 sin6;
. . .
sin6.sin6_family = AF_INET6;
sin6.sin6_flowinfo = 0;
sin6.sin6_port = htons(23);
sin6.sin6_addr = in6addr_any; /* structure assignment */
. . .
if (bind(s, (struct sockaddr *) &sin6, sizeof(sin6)) == -1)
. . .
The other version is a symbolic constant named IN6ADDR_ANY_INIT and is
defined in <netinet/in.h>. This constant can be used to initialize an
in6_addr structure:
struct in6_addr anyaddr = IN6ADDR_ANY_INIT;
Note that this constant can be used ONLY at declaration time. It can
not be used to assign a previously declared in6_addr structure. For
example, the following code will not work:
/* This is the WRONG way to assign an unspecified address */
struct sockaddr_in6 sin6;
. . .
sin6.sin6_addr = IN6ADDR_ANY_INIT; /* will NOT compile */
Be aware that the IPv4 INADDR_xxx constants are all defined in host byte
order but the IPv6 IN6ADDR_xxx constants and the IPv6 in6addr_xxx
externals are defined in network byte order.
3.9 IPv6 Loopback Address
Applications may need to send UDP packets to, or originate TCP
connections to, services residing on the local node. In IPv4, they can
do this by using the constant IPv4 address INADDR_LOOPBACK in their
connect(), sendto(), or sendmsg() call.
IPv6 also provides a loopback address to contact local TCP and UDP
services. Like the unspecified address, the IPv6 loopback address is
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 11]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
provided in two forms -- a global variable and a symbolic constant.
The global variable is an in6_addr structure named "in6addr_loopback."
The extern declaration for this variable is defined in <netinet/in.h>:
extern const struct in6_addr in6addr_loopback;
Applications use in6addr_loopback as they would use INADDR_LOOPBACK in
IPv4 applications (but beware of the byte ordering difference mentioned
at the end of the previous section). For example, to open a TCP
connection to the local telnet server, an application could use the
following code:
struct sockaddr_in6 sin6;
. . .
sin6.sin6_family = AF_INET6;
sin6.sin6_flowinfo = 0;
sin6.sin6_port = htons(23);
sin6.sin6_addr = in6addr_loopback; /* structure assignment */
. . .
if (connect(s, (struct sockaddr *) &sin6, sizeof(sin6)) == -1)
. . .
The symbolic constant is named IN6ADDR_LOOPBACK_INIT and is defined in
<netinet/in.h>. It can be used at declaration time ONLY; for example:
struct in6_addr loopbackaddr = IN6ADDR_LOOPBACK_INIT;
Like IN6ADDR_ANY_INIT, this constant cannot be used in an assignment to
a previously declared IPv6 address variable.
3.10 Portability Additions
One simple addition to the sockets API that can help application writers
is the "struct sockaddr_storage". This data structure can simplify
writing portable code across multiple address families and platforms.
This data structure is designed with the following goals.
- Large enough to accommodate all supported protocol-specific address
structures.
- Aligned at an appropriate boundary so that pointers to it can be cast
as pointers to protocol specific address structures and used to
access the fields of those structures without alignment problems.
The sockaddr_storage structure contains field ss_family which is of type
sa_family_t. When a sockaddr_storage structure is cast to a sockaddr
structure, the ss_family field of the sockaddr_storage structure maps
onto the sa_family field of the sockaddr structure. When a
sockaddr_storage structure is cast as a protocol specific address
structure, the ss_family field maps onto a field of that structure that
is of type sa_family_t and that identifies the protocol's address
family.
An example implementation design of such a data structure would be as
follows.
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 12]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
/*
* Desired design of maximum size and alignment
*/
#define _SS_MAXSIZE 128 /* Implementation specific max size */
#define _SS_ALIGNSIZE (sizeof (int64_t))
/* Implementation specific desired alignment */
/*
* Definitions used for sockaddr_storage structure paddings design.
*/
#define _SS_PAD1SIZE (_SS_ALIGNSIZE - sizeof (sa_family_t))
#define _SS_PAD2SIZE (_SS_MAXSIZE - (sizeof (sa_family_t)+
_SS_PAD1SIZE + _SS_ALIGNSIZE))
struct sockaddr_storage {
sa_family_t ss_family; /* address family */
/* Following fields are implementation specific */
char __ss_pad1[_SS_PAD1SIZE];
/* 6 byte pad, this is to make implementation
/* specific pad up to alignment field that */
/* follows explicit in the data structure */
int64_t __ss_align; /* field to force desired structure */
/* storage alignment */
char __ss_pad2[_SS_PAD2SIZE];
/* 112 byte pad to achieve desired size, */
/* _SS_MAXSIZE value minus size of ss_family */
/* __ss_pad1, __ss_align fields is 112 */
};
The above example implementation illustrates a data structure which
will align on a 64-bit boundary. An implementation-specific field
"_ss_align" along "_ss_pad1" is used to force a 64-bit alignment which
covers proper alignment good enough for needs of sockaddr_in6 (IPv6),
sockaddr_in (IPv4) address data structures. The size of padding fields
_ss_pad1 depends on the chosen alignment boundary. The size of padding
field _ss_pad2 depends on the value of overall size chosen for the total
size of the structure. This size and alignment are represented in the
above example by implementation specific (not required) constants
_SS_MAXSIZE (chosen value 128) and _SS_ALIGNMENT (with chosen value 8).
Constants _SS_PAD1SIZE (derived value 6) and _SS_PAD2SIZE (derived value
112) are also for illustration and not required. The implementation specific
definitions and structure field names above start with an underscore to
denote implementation private namespace. Portable code is not expected to
access or reference those fields or constants.
On implementations where sockaddr data structure includes a "sa_len",
field this data structure would look like this:
/*
* Definitions used for sockaddr_storage structure paddings design.
*/
#define _SS_PAD1SIZE (_SS_ALIGNSIZE -
(sizeof (uint8_t) + sizeof (sa_family_t))
#define _SS_PAD2SIZE (_SS_MAXSIZE - (sizeof (sa_family_t)+
_SS_PAD1SIZE + _SS_ALIGNSIZE))
struct sockaddr_storage {
uint8_t ss_len; /* address length */
sa_family_t ss_family; /* address family */
/* Following fields are implementation specific */
char __ss_pad1[_SS_PAD1SIZE];
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 13]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
/* 6 byte pad, this is to make implementation
/* specific pad up to alignment field that */
/* follows explicit in the data structure */
int64_t __ss_align; /* field to force desired structure */
/* storage alignment */
char __ss_pad2[_SS_PAD2SIZE];
/* 112 byte pad to achieve desired size, */
/* _SS_MAXSIZE value minus size of ss_len, */
/* __ss_family, __ss_pad1, __ss_align fields is 112 */
};
4. Interface Identification
This API uses an interface index (a small positive integer) to identify
the local interface on which a multicast group is joined (Section 5.3).
Additionally, the advanced API [4] uses these same interface indexes to
identify the interface on which a datagram is received, or to specify
the interface on which a datagram is to be sent.
Interfaces are normally known by names such as "le0", "sl1", "ppp2", and
the like. On Berkeley-derived implementations, when an interface is
made known to the system, the kernel assigns a unique positive integer
value (called the interface index) to that interface. These are small
positive integers that start at 1. (Note that 0 is never used for an
interface index.) There may be gaps so that there is no current
interface for a particular positive interface index.
This API defines two functions that map between an interface name and
index, a third function that returns all the interface names and
indexes, and a fourth function to return the dynamic memory allocated by
the previous function. How these functions are implemented is left up
to the implementation. 4.4BSD implementations can implement these
functions using the existing sysctl() function with the NET_RT_IFLIST
command. Other implementations may wish to use ioctl() for this
purpose.
4.1 Name-to-Index
The first function maps an interface name into its corresponding index.
#include <net/if.h>
unsigned int if_nametoindex(const char *ifname);
If the specified interface name does not exist, the return value is 0,
and errno is set to ENXIO. If there was a system error (such as
running out of memory), the return value is 0 and errno is set to the
proper value (e.g., ENOMEM).
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 14]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
4.2 Index-to-Name
The second function maps an interface index into its corresponding name.
#include <net/if.h>
char *if_indextoname(unsigned int ifindex, char *ifname);
The ifname argument must point to a buffer of at least IF_NAMESIZE bytes
into which the interface name corresponding to the specified index is
returned. (IF_NAMESIZE is also defined in <net/if.h> and its value
includes a terminating null byte at the end of the interface name.) This
pointer is also the return value of the function. If there is no
interface corresponding to the specified index, NULL is returned, and
errno is set to ENXIO, if there was a system error (such as running out
of memory), if_indextoname returns NULL and errno would be set to the
proper value (e.g., ENOMEM).
4.3 Return All Interface Names and Indexes
The if_nameindex structure holds the information about a single
interface and is defined as a result of including the <net/if.h> header.
struct if_nameindex {
unsigned int if_index; /* 1, 2, ... */
char *if_name; /* null terminated name: "le0", ... */
};
The final function returns an array of if_nameindex structures, one
structure per interface.
struct if_nameindex *if_nameindex(void);
The end of the array of structures is indicated by a structure with an
if_index of 0 and an if_name of NULL. The function returns a NULL
pointer upon an error, and would set errno to the appropriate value.
The memory used for this array of structures along with the interface
names pointed to by the if_name members is obtained dynamically. This
memory is freed by the next function.
4.4 Free Memory
The following function frees the dynamic memory that was allocated by
if_nameindex().
#include <net/if.h>
void if_freenameindex(struct if_nameindex *ptr);
The argument to this function must be a pointer that was returned by
if_nameindex().
Currently net/if.h doesn't have prototype definitions for functions and
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 15]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
it is recommended that these definitions be defined in net/if.h as well
as the struct if_nameindex{}.
5. Socket Options
A number of new socket options are defined for IPv6. All of these new
options are at the IPPROTO_IPV6 level. That is, the "level" parameter
in the getsockopt() and setsockopt() calls is IPPROTO_IPV6 when using
these options. The constant name prefix IPV6_ is used in all of the new
socket options. This serves to clearly identify these options as
applying to IPv6.
The declaration for IPPROTO_IPV6, the new IPv6 socket options, and
related constants defined in this section are obtained by including the
header <netinet/in.h>.
5.1 Unicast Hop Limit
A new setsockopt() option controls the hop limit used in outgoing
unicast IPv6 packets. The name of this option is IPV6_UNICAST_HOPS, and
it is used at the IPPROTO_IPV6 layer. The following example illustrates
how it is used:
int hoplimit = 10;
if (setsockopt(s, IPPROTO_IPV6, IPV6_UNICAST_HOPS,
(char *) &hoplimit, sizeof(hoplimit)) == -1)
perror("setsockopt IPV6_UNICAST_HOPS");
When the IPV6_UNICAST_HOPS option is set with setsockopt(), the option
value given is used as the hop limit for all subsequent unicast packets
sent via that socket. If the option is not set, the system selects a
default value. The integer hop limit value (called x) is interpreted as
follows:
x < -1: return an error of EINVAL
x == -1: use kernel default
0 <= x <= 255: use x
x >= 256: return an error of EINVAL
The IPV6_UNICAST_HOPS option may be used with getsockopt() to determine
the hop limit value that the system will use for subsequent unicast
packets sent via that socket. For example:
int hoplimit;
socklen_t len = sizeof(hoplimit);
if (getsockopt(s, IPPROTO_IPV6, IPV6_UNICAST_HOPS,
(char *) &hoplimit, &len) == -1)
perror("getsockopt IPV6_UNICAST_HOPS");
else
printf("Using %d for hop limit.\n", hoplimit);
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 16]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
5.2 Sending and Receiving Multicast Packets
IPv6 applications may send UDP multicast packets by simply specifying an
IPv6 multicast address in the address argument of the sendto() function.
Three socket options at the IPPROTO_IPV6 layer control some of the
parameters for sending multicast packets. Setting these options is not
required: applications may send multicast packets without using these
options. The setsockopt() options for controlling the sending of
multicast packets are summarized below. These three options can also be
used with getsockopt().
IPV6_MULTICAST_IF
Set the interface to use for outgoing multicast packets.
The argument is the index of the interface to use.
Argument type: unsigned int
IPV6_MULTICAST_HOPS
Set the hop limit to use for outgoing multicast packets.
(Note a separate option - IPV6_UNICAST_HOPS - is
provided to set the hop limit to use for outgoing
unicast packets.)
The interpretation of the argument is the same
as for the IPV6_UNICAST_HOPS option:
x < -1: return an error of EINVAL
x == -1: use kernel default
0 <= x <= 255: use x
x >= 256: return an error of EINVAL
If IPV6_MULTICAST_HOPS is not set, the default is 1
(same as IPv4 today)
Argument type: int
IPV6_MULTICAST_LOOP
If a multicast datagram is sent to a group to which the sending host
itself belongs (on the outgoing interface), a copy of the datagram is
looped back by the IP layer for local delivery if this option is set to
1. If this option is set to 0 a copy is not looped back. Other option
values return an error of EINVAL.
If IPV6_MULTICAST_LOOP is not set, the default is 1 (loopback; same as
IPv4 today).
Argument type: unsigned int
The reception of multicast packets is controlled by the two setsockopt()
options summarized below. An error of EOPNOTSUPP is returned if these
two options are used with getsockopt().
IPV6_JOIN_GROUP
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 17]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
Join a multicast group on a specified local interface.
If the interface index is specified as 0,
the kernel chooses the local interface.
For example, some kernels look up the multicast group
in the normal IPv6 routing table and use the resulting interface.
Argument type: struct ipv6_mreq
IPV6_LEAVE_GROUP
Leave a multicast group on a specified interface.
Argument type: struct ipv6_mreq
The argument type of both of these options is the ipv6_mreq structure,
defined as a result of including the <netinet/in.h> header;
struct ipv6_mreq {
struct in6_addr ipv6mr_multiaddr; /* IPv6 multicast addr */
unsigned int ipv6mr_interface; /* interface index */
};
Note that to receive multicast datagrams a process must join the
multicast group and bind the UDP port to which datagrams will be sent.
Some processes also bind the multicast group address to the socket, in
addition to the port, to prevent other datagrams destined to that same
port from being delivered to the socket.
5.3 IPV6_V6ONLY option for AF_INET6 Sockets
This socket option restricts AF_INET6 sockets to IPv6 communications
only. As stated in section <3.7 Compatibility with IPv4 Nodes>,
AF_INET6 sockets may be used for both IPv4 and IPv6 communications. Some
applications may want to restrict their use of an AF_INET6 socket to
IPv6 communications only. For these applications the IPV6_V6ONLY socket
option is defined. When this option is turned on, the socket can be
used to send and receive IPv6 packets only. This is an IPPROTO_IPV6
level option. This option takes an int value. This is a boolean
option. By default this option is turned off.
Here is an example of setting this option:
int on = 1;
if (setsockopt(s, IPPROTO_IPV6, IPV6_V6ONLY,
(char *)&on, sizeof(on)) == -1)
perror("setsockopt IPV6_V6ONLY");
else
printf("IPV6_V6ONLY set0);
Note - This option has no effect on the use of IPv4 Mapped addresses
which enter a node as a valid IPv6 addresses for IPv6 communications as
defined by Stateless IP/ICMP Translation Algorithm (SIIT) [8].
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 18]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
6. Library Functions
New library functions are needed to perform a variety of operations with
IPv6 addresses. Functions are needed to lookup IPv6 addresses in the
Domain Name System (DNS). Both forward lookup (nodename-to-address
translation) and reverse lookup (address-to-nodename translation) need
to be supported. Functions are also needed to convert IPv6 addresses
between their binary and textual form.
We note that the two existing functions, gethostbyname() and
gethostbyaddr(), are left as-is. New functions are defined to handle
both IPv4 and IPv6 addresses.
The commonly used function gethostbyname() is inadequate for many
applications, first because it provides no way for the caller to specify
anything about the types of addresses desired (IPv4 only, IPv6 only,
IPv4-mapped IPv6 are OK, etc.), and second because many implementations
of this function are not thread safe. RFC 2133 defined a function named
gethostbyname2() but this function was also inadequate, first because
its use required setting a global option (RES_USE_INET6) when IPv6
addresses were required, and second because a flag argument is needed to
provide the caller with additional control over the types of addresses
required.
6.1 Protocol-Independent Nodename and Service Name Translation
Nodename-to-address translation is done in a protocol-independent
fashion using the getaddrinfo() function that is taken from the
Institute of Electrical and Electronic Engineers IEEE 1003.1-200x
(POSIX) draft specification [3].
The official specification for this function will be the final IEEE
standard. In addition this specification is not specifying all
parameter possibilities for this function, but only the parameters that
can be provided to support IPv4 and IPv6 communications to support this
specification. This is beyond the scope of this document and additional
work on this function will be done by the Austin (IEEE/ISO/TOG) Group.
#include <sys/socket.h>
#include <netdb.h>
int getaddrinfo(const char *nodename, const char *servname,
const struct addrinfo *hints, struct addrinfo **res);
void freeaddrinfo(struct addrinfo *ai);
struct addrinfo {
int ai_flags; /* AI_PASSIVE, AI_CANONNAME, AI_NUMERICHOST, .. */
int ai_family; /* PF_xxx */
int ai_socktype; /* SOCK_xxx */
int ai_protocol; /* 0 or IPPROTO_xxx for IPv4 and IPv6 */
socklen_t ai_addrlen; /* length of ai_addr */
char *ai_canonname; /* canonical name for nodename */
struct sockaddr *ai_addr; /* binary address */
struct addrinfo *ai_next; /* next structure in linked list */
};
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 19]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
The getaddrinfo ( ) function translates the name of a service
location (for example, a host name) and/or a service name and returns
a set of socket addresses and associated information to be used in
creating a socket with which to address the specified service.
The nodename and servname arguments are either null pointers or
pointers to null-terminated strings. One or both of these two
arguments must be a non-null pointer.
The format of a valid name depends on the protocol family or
families. If a specific family is not given and the name could be
interpreted as valid within multiple supported families, the
implementation will attempt to resolve the name in all supported
families and, all successful results will be returned.
If the nodename argument is not null, it can be a descriptive name or
can be an address string. If the specified address family is AF_INET,
or AF_UNSPEC, the permissable nodename argument is specified as
defined in inet_pton(). If the specified address family is AF_INET6
or AF_UNSPEC, the permissable nodename argument is specified as
defined in [5].
If nodename is not null, the requested service location is named by
nodename; otherwise, the requested service location is local to the
caller.
If servname is null, the call returns network-level addresses for the
specified nodename. If servname is not null, it is a null-terminated
character string identifying the requested service. This can be
either a descriptive name or a numeric representation suitable for
use with the address family or families. If the specified address
family is AF_INET, AF_INET6 or AF_UNSPEC, the service can be
specified as a string specifying a decimal port number.
If the argument hints is not null, it refers to a structure
containing input values that may direct the operation by providing
options and by limiting the returned information to a specific socket
type, address family and/or protocol. In this hints structure every
member other than ai_flags, ai_family, ai_socktype and ai_protocol
must be zero or a null pointer. A value of AF_UNSPEC for ai_family
means that the caller will accept any protocol family. A value of
zero for ai_socktype means that the caller will accept any socket
type. A value of zero for ai_protocol means that the caller will
accept any protocol. If hints is a null pointer, the behavior must be
as if it referred to a structure containing the value zero for the
ai_flags, ai_socktype and ai_protocol fields, and AF_UNSPEC for the
ai_family field.
Note:
1. If the caller handles only TCP and not UDP, for example, then the
ai_protocol member of the hints structure should be set to
IPPROTO_TCP when getaddrinfo ( ) is called.
2. If the caller handles only IPv4 and not IPv6, then the ai_family
member of the hints structure should be set to PF_INET when
getaddrinfo ( ) is called.
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 20]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
The ai_flags field to which hints parameter points must have the
value zero or be the bitwise OR of one or more of the values
AI_PASSIVE, AI_CANONNAME, AI_NUMERICHOST, AI_NUMERICSERV,
AI_V4MAPPED, AI_ALL, and AI_ADDRCONFIG.
The AI_PASSIVE flag in the ai_flags member of the hints structure
specifies how to fill in the IP address portion of the socket address
structure. If the AI_PASSIVE flag is specified, then the returned
address information must be suitable for use in binding a socket for
accepting incoming connections for the specified service (i.e. a call
to bind()). In this case, if the nodename argument is null, then the
IP address portion of the socket address structure will be set to
INADDR_ANY for an IPv4 address or IN6ADDR_ANY_INIT for an IPv6
address. If the AI_PASSIVE bit is not set, the returned address
information must be suitable for a call to connect( ) (for a
connection-mode protocol) or for a call to connect(), sendto() or
sendmsg( ) (for a connectionless protocol). In this case, if the
nodename argument is null, then the IP address portion of the socket
address structure will be set to the loopback address. This flag is
ignored if the nodename argument is not null.
If the flag AI_CANONNAME is specified and the nodename argument is
not null, the function attempts to determine the canonical name
corresponding to nodename (for example, if nodename is an alias or
shorthand notation for a complete name).
If the flag AI_NUMERICHOST is specified then a non-null nodename
string must be a numeric host address string. Otherwise an error of
[EAI_NONAME] is returned. This flag prevents any type of name
resolution service (for example, the DNS) from being invoked.
If the flag AI_NUMERICSERV is specified then a non-null servname
string must be a numeric port string. Otherwise an error [EAI_NONAME]
is returned. This flag prevents any type of name resolution service
(for example, NIS+) from being invoked.
If the AI_V4MAPPED flag is specified along with an ai_family of
AF_INET6, then the caller will accept IPv4-mapped IPv6 addresses.
That is, if no AAAA or A6, records are found then a query is made for
A records and any found are returned as IPv4-mapped IPv6 addresses
(ai_addrlen will be 16). The AI_V4MAPPED flag is ignored unless
ai_family equals AF_INET6.
The AI_ALL flag is used in conjunction with the AI_V4MAPPED flag, and
is only used with an ai_family of AF_INET6. When AI_ALL is logically
or'd with AI_V4MAPPED flag then the caller will accept all addresses:
IPv6 and IPv4-mapped IPv6. A query is first made for AAAA/A6 records
and if successful, the IPv6 addresses are returned. Another query is
then made for A records and any found are returned as IPv4-mapped
IPv6 addresses (ai_addrlen will be 16). This flag is ignored unless
ai_family equals AF_INET6.
Note:
When ai_family is not specified (AF_UNSPEC), AI_V4MAPPED and
AI_ALL flags will only be used if AF_INET6 is supported.
If the AI_ADDRCONFIG flag is specified then a query for AAAA or A6
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 21]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
records should occur only if the node has at least one IPv6 source
address configured and a query for A records should occur only if the
node has at least one IPv4 source address configured. The loopback
address is not considered for this case as valid as a configured
sources address.
The ai_socktype field to which argument hints points specifies the
socket type for the service. If a specific socket type is not given
(for example, a value of zero) and the service name could be
interpreted as valid with multiple supported socket types, the
implementation will attempt to resolve the service name for all
supported socket types and, all successful results will be returned.
A non-zero socket type value will limit the returned information to
values with the specified socket type.
The freeaddrinfo ( ) function frees one or more addrinfo structures
returned by getaddrinfo ( ), along with any additional storage
associated with those structures. If the ai_next field of the
structure is not null, the entire list of structures is freed. The
freeaddrinfo () function must support the freeing of arbitrary
sublists of an addrinfo list originally returned by getaddrinfo ().
Functions getaddrinfo ( ) and freeaddrinfo ( ) must be thread-safe.
A zero return value for getaddrinfo ( ) indicates successful
completion; a non-zero return value indicates failure.
Upon successful return of getaddrinfo ( ), the location to which res
points refers to a linked list of addrinfo structures, each of which
specifies a socket address and information for use in creating a
socket with which to use that socket address. The list must include
at least one addrinfo structure. The ai_next field of each structure
contains a pointer to the next structure on the list, or a null
pointer if it is the last structure on the list. Each structure on
the list includes values for use with a call to the socket( )
function, and a socket address for use with the connect() function
or, if the AI_PASSIVE flag was specified, for use with the bind( )
function. The fields ai_family, ai_socktype, and ai_protocol are
usable as the arguments to the socket() function to create a socket
suitable for use with the returned address. The fields ai_addr and
ai_addrlen are usable as the arguments to the connect() or bind( )
functions with such a socket, according to the AI_PASSIVE flag.
If nodename is not null, and if requested by the AI_CANONNAME flag,
the ai_canonname field of the first returned addrinfo structure
points to a null-terminated string containing the canonical name
corresponding to the input nodename; if the canonical name is not
available, then ai_canonname refers to the argument nodename or a
string with the same contents. The contents of the ai_flags field of
the returned structures is undefined.
All fields in socket address structures returned by getaddrinfo ( )
that are not filled in through an explicit argument (for example,
sin6_flowinfo) must be set to zero.
Note: This makes it easier to compare socket address structures.
Error Return Values:
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 22]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
[EAI_AGAIN] The name could not be resolved at this time. Future
attempts may succeed.
[EAI_BADFLAGS] The flags parameter had an invalid value.
[EAI_FAIL] A non-recoverable error occurred when attempting to
resolve the name.
[EAI_FAMILY] The address family was not recognized.
[EAI_MEMORY] There was a memory allocation failure when trying to
allocate storage for the return value.
[EAI_NONAME] The name does not resolve for the supplied parameters.
Neither nodename nor servname were passed. At least one
of these must be passed.
[EAI_SERVICE] The service passed was not recognized for the specified
socket type.
[EAI_SOCKTYPE] The intended socket type was not recognized.
[EAI_SYSTEM] A system error occurred; the error code can be found in
errno.
#include <sys/socket.h>
#include <netdb.h>
char *gai_strerror(int ecode);
The argument is one of the EAI_xxx values defined earlier and the return
value points to a string describing the error. If the argument is not
one of the EAI_xxx values, the function still returns a pointer to a
string whose contents indicate an unknown error.
6.2 Socket Address Structure to Nodename and Service Name
The official specification for this function will be the final Austin
Group standard update to getaddrinfo(), and will incorporate this
function. In addition this specification is not specifying all
parameter possibilities for this function, but only the parameters that
can be provided to support IPv4 and IPv6 communications to support this
specification. This is beyond the scope of this document and additional
work on this function will be done by the Austin group.
#include <sys/socket.h>
#include <netdb.h>
int getnameinfo(const struct sockaddr *sa, socklen_t salen,
char *host, socklen_t hostlen,
char *serv, socklen_t servlen,
int flags);
The getnameinfo( ) translates a socket address to a node name and
service location, all of which are defined as with getaddrinfo ().
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 23]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
The argument sa points to a socket address structure to be translated.
If the argument node is non-NULL and the argument nodelen is nonzero,
then the argument node points to a buffer able to contain up to nodelen
characters that will receive the node name as a null-terminated string.
If the argument node is NULL or the argument nodelen is zero, the node
name will not be returned. If the node<64>s name cannot be located, the
numeric form of the nodes address is returned instead of its name. If
the sa argument is an IPv6 address the returned nodename may be in the
format as defined in [5].
If the argument service is non-NULL and the argument servicelen is
nonzero, then the argument service points to a buffer able to contain up
to servicelen characters that will receive the service name as a null-
terminated string. If the argument service is NULL or the argument
servicelen is zero, the service name will not be returned. If the
service name cannot be located, the numeric form of the service address
(for example, its port number) is returned instead of its name.
The arguments node and service cannot both be NULL.
The flags argument is a flag that changes the default actions of the
function. By default the fully-qualified domain name (FQDN) for the host
is returned, but
- If the flag bit NI_NOFQDN is set, only the nodename portion of the
FQDN is returned for local hosts.
- If the flag bit NI_NUMERICHOST is set, the numeric form of the
host's address is returned instead of its name, under all
circumstances.
- If the flag bit NI_NAMEREQD is set, an error is returned if the
host<73>s name cannot be located.
- If the flag bit NI_NUMERICSERV is set, the numeric form of the
service address is returned (for example, its port number) instead of
its name, under all circumstances.
- If the flag bit NI_NUMERICSCOPE is set, the numeric form of the
scope identifier is returned (for example, interface index)
instead of its name. This flag is ignored if the sa argument is
not an IPv6 address.
- If the flag bit NI_DGRAM is set, this indicates that the service is
a datagram service (SOCK_DGRAM). The default behavior is to assume that
the service is a stream service (SOCK_STREAM).
Note:
1. The three NI_NUMERICxxx flags are required to support the "-n"
flags that many commands support.
2. The NI_DGRAM flag is required for the new AF_INET/AF_INET6 port
numbers (for example, 512-514) that represent different services
for UDP and TCP.
Function getnameinfo() must be thread safe.
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 24]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
A zero return value for getnameinfo( ) indicates successful completion;
a non-zero return value indicates failure.
On successful completion, function getnameinfo( ) returns the node and
service names, if requested, in the buffers provided. The returned names
are always null-terminated strings.
Error Return Values:
[EAI_AGAIN] The name could not be resolved at this time.
Future attempts may succeed.
[EAI_BADFLAGS] The flags had an invalid value.
[EAI_FAIL] A non-recoverable error occurred.
[EAI_FAMILY] The address family was not recognized or the address
length was invalid for the specified family.
[EAI_MEMORY] There was a memory allocation failure.
[EAI_NONAME] The name does not resolve for the supplied parameters.
NI_NAMEREQD is set and the host<73>s name cannot be located, or
both nodename and servname were null.
[EAI_SYSTEM] A system error occurred. The error code can be found in
errno.
6.3 Address Conversion Functions
The two functions inet_addr() and inet_ntoa() convert an IPv4 address
between binary and text form. IPv6 applications need similar functions.
The following two functions convert both IPv6 and IPv4 addresses:
#include <sys/socket.h>
#include <arpa/inet.h>
int inet_pton(int af, const char *src, void *dst);
const char *inet_ntop(int af, const void *src,
char *dst, socklen_t size);
The inet_pton() function converts an address in its standard text
presentation form into its numeric binary form. The af argument
specifies the family of the address. Currently the AF_INET and AF_INET6
address families are supported. The src argument points to the string
being passed in. The dst argument points to a buffer into which the
function stores the numeric address. The address is returned in network
byte order. Inet_pton() returns 1 if the conversion succeeds, 0 if the
input is not a valid IPv4 dotted-decimal string or a valid IPv6 address
string, or -1 with errno set to EAFNOSUPPORT if the af argument is
unknown. The calling application must ensure that the buffer referred
to by dst is large enough to hold the numeric address (e.g., 4 bytes for
AF_INET or 16 bytes for AF_INET6).
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 25]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
If the af argument is AF_INET, the function accepts a string in the
standard IPv4 dotted-decimal form:
ddd.ddd.ddd.ddd
where ddd is a one to three digit decimal number between 0 and 255.
Note that many implementations of the existing inet_addr() and
inet_aton() functions accept nonstandard input: octal numbers,
hexadecimal numbers, and fewer than four numbers. inet_pton() does not
accept these formats.
If the af argument is AF_INET6, then the function accepts a string in
one of the standard IPv6 text forms defined in Section 2.2 of the
addressing architecture specification [2].
The inet_ntop() function converts a numeric address into a text string
suitable for presentation. The af argument specifies the family of the
address. This can be AF_INET or AF_INET6. The src argument points to a
buffer holding an IPv4 address if the af argument is AF_INET, or an IPv6
address if the af argument is AF_INET6, the address must be in network
byte order. The dst argument points to a buffer where the function will
store the resulting text string. The size argument specifies the size
of this buffer. The application must specify a non-NULL dst argument.
For IPv6 addresses, the buffer must be at least 46-octets. For IPv4
addresses, the buffer must be at least 16-octets. In order to allow
applications to easily declare buffers of the proper size to store IPv4
and IPv6 addresses in string form, the following two constants are
defined in <netinet/in.h>:
#define INET_ADDRSTRLEN 16
#define INET6_ADDRSTRLEN 46
The inet_ntop() function returns a pointer to the buffer containing the
text string if the conversion succeeds, and NULL otherwise. Upon
failure, errno is set to EAFNOSUPPORT if the af argument is invalid or
ENOSPC if the size of the result buffer is inadequate.
6.4 Address Testing Macros
The following macros can be used to test for special IPv6 addresses.
#include <netinet/in.h>
int IN6_IS_ADDR_UNSPECIFIED (const struct in6_addr *);
int IN6_IS_ADDR_LOOPBACK (const struct in6_addr *);
int IN6_IS_ADDR_MULTICAST (const struct in6_addr *);
int IN6_IS_ADDR_LINKLOCAL (const struct in6_addr *);
int IN6_IS_ADDR_SITELOCAL (const struct in6_addr *);
int IN6_IS_ADDR_V4MAPPED (const struct in6_addr *);
int IN6_IS_ADDR_V4COMPAT (const struct in6_addr *);
int IN6_IS_ADDR_MC_NODELOCAL(const struct in6_addr *);
int IN6_IS_ADDR_MC_LINKLOCAL(const struct in6_addr *);
int IN6_IS_ADDR_MC_SITELOCAL(const struct in6_addr *);
int IN6_IS_ADDR_MC_ORGLOCAL (const struct in6_addr *);
int IN6_IS_ADDR_MC_GLOBAL (const struct in6_addr *);
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 26]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
The first seven macros return true if the address is of the specified
type, or false otherwise. The last five test the scope of a multicast
address and return true if the address is a multicast address of the
specified scope or false if the address is either not a multicast
address or not of the specified scope. Note that IN6_IS_ADDR_LINKLOCAL
and IN6_IS_ADDR_SITELOCAL return true only for the two local-use IPv6
unicast addresses. These two macros do not return true for IPv6
multicast addresses of either link-local scope or site-local scope.
7. Summary of New Definitions
The following list summarizes the constants, structure, and extern
definitions discussed in this memo, sorted by header.
<net/if.h> IF_NAMESIZE
<net/if.h> struct if_nameindex{};
<netdb.h> AI_ADDRCONFIG
<netdb.h> AI_DEFAULT
<netdb.h> AI_ALL
<netdb.h> AI_CANONNAME
<netdb.h> AI_NUMERICHOST
<netdb.h> AI_PASSIVE
<netdb.h> AI_V4MAPPED
<netdb.h> EAI_AGAIN
<netdb.h> EAI_BADFLAGS
<netdb.h> EAI_FAIL
<netdb.h> EAI_FAMILY
<netdb.h> EAI_MEMORY
<netdb.h> EAI_NONAME
<netdb.h> EAI_SERVICE
<netdb.h> EAI_SOCKTYPE
<netdb.h> EAI_SYSTEM
<netdb.h> NI_DGRAM
<netdb.h> NI_MAXHOST
<netdb.h> NI_MAXSERV
<netdb.h> NI_NAMEREQD
<netdb.h> NI_NOFQDN
<netdb.h> NI_NUMERICHOST
<netdb.h> NI_NUMERICSERV
<netdb.h> struct addrinfo{};
<netinet/in.h> IN6ADDR_ANY_INIT
<netinet/in.h> IN6ADDR_LOOPBACK_INIT
<netinet/in.h> INET6_ADDRSTRLEN
<netinet/in.h> INET_ADDRSTRLEN
<netinet/in.h> IPPROTO_IPV6
<netinet/in.h> IPV6_JOIN_GROUP
<netinet/in.h> IPV6_LEAVE_GROUP
<netinet/in.h> IPV6_MULTICAST_HOPS
<netinet/in.h> IPV6_MULTICAST_IF
<netinet/in.h> IPV6_MULTICAST_LOOP
<netinet/in.h> IPV6_UNICAST_HOPS
<netinet/in.h> SIN6_LEN
<netinet/in.h> extern const struct in6_addr in6addr_any;
<netinet/in.h> extern const struct in6_addr in6addr_loopback;
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 27]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
<netinet/in.h> struct in6_addr{};
<netinet/in.h> struct ipv6_mreq{};
<netinet/in.h> struct sockaddr_in6{};
<sys/socket.h> AF_INET6
<sys/socket.h> PF_INET6
<sys/socket.h> struct sockaddr_storage;
The following list summarizes the function and macro prototypes
discussed in this memo, sorted by header.
<arpa/inet.h> int inet_pton(int, const char *, void *);
<arpa/inet.h> const char *inet_ntop(int, const void *,
char *, socklen_t);
<net/if.h> char *if_indextoname(unsigned int, char *);
<net/if.h> unsigned int if_nametoindex(const char *);
<net/if.h> void if_freenameindex(struct if_nameindex *);
<net/if.h> struct if_nameindex *if_nameindex(void);
<netdb.h> int getaddrinfo(const char *, const char *,
const struct addrinfo *,
struct addrinfo **);
<netdb.h> int getnameinfo(const struct sockaddr *, socklen_t,
char *, socklen_t, char *, socklen_t, int);
<netdb.h> void freeaddrinfo(struct addrinfo *);
<netdb.h> char *gai_strerror(int);
<netinet/in.h> int IN6_IS_ADDR_LINKLOCAL(const struct in6_addr *);
<netinet/in.h> int IN6_IS_ADDR_LOOPBACK(const struct in6_addr *);
<netinet/in.h> int IN6_IS_ADDR_MC_GLOBAL(const struct in6_addr *);
<netinet/in.h> int IN6_IS_ADDR_MC_LINKLOCAL(const struct in6_addr *);
<netinet/in.h> int IN6_IS_ADDR_MC_NODELOCAL(const struct in6_addr *);
<netinet/in.h> int IN6_IS_ADDR_MC_ORGLOCAL(const struct in6_addr *);
<netinet/in.h> int IN6_IS_ADDR_MC_SITELOCAL(const struct in6_addr *);
<netinet/in.h> int IN6_IS_ADDR_MULTICAST(const struct in6_addr *);
<netinet/in.h> int IN6_IS_ADDR_SITELOCAL(const struct in6_addr *);
<netinet/in.h> int IN6_IS_ADDR_UNSPECIFIED(const struct in6_addr *);
<netinet/in.h> int IN6_IS_ADDR_V4COMPAT(const struct in6_addr *);
<netinet/in.h> int IN6_IS_ADDR_V4MAPPED(const struct in6_addr *);
8. Security Considerations
IPv6 provides a number of new security mechanisms, many of which need to
be accessible to applications. Companion memos detailing the extensions
to the socket interfaces to support IPv6 security are being written.
9. Year 2000 Considerations
There are no issues for this draft concerning the Year 2000 issue
regarding the use of dates.
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 28]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
Changes made to rfc2553bis-02 to rfc2553bis-03
1. Edits only.
Changes made to rfc2553bis-01 to rfc2553bis-02
1. Updated all references to comply with latest IEEEE work on
socket APIs and changed all remaining size_t to socklen_t.
2. Edits caught.
Changes made to rfc2553bis-00 to rfc2553bis-01
1. Removed all references to getipnodebyname() and
getipnodebyaddr().
2. Added IPV6_V6ONLY Socket IP level option to permit nodes
to not process IPv4 packets as IPv4 Mapped addresses
in implementations.
3. Added note to getaddrinfo() and getnameinfo()
that final specification of parameter associations for
these functions will be done by Austin.
4. Added SIIT to references and added new contributors.
Changes made rfc2553 to rfc2553bis-00:
1. Updated Portability Section 3.10 to conform to XNS 5.2.
2. Updated getaddrinfo(), getnameinfo(), to conform to XNS 5.2.
3. Added references to Scope Architecture, Scope Routing, and
Extension Format for Scoped Addresses work in progress.
4. Added NI_NUMERICSCOPE flag to getnameinfo().
5. Added qualification to getipnodebyname/addr() functions that
they will not work as is with scope identifiers with IPv6, and
getaddrinfo/getnameinfo should be used.
6. Added DNS A6 record notation to AAAA and added ip6.arpa as new
PTR record domain.
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 29]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
Acknowledgments
This specification's evolution and completeness were significantly
influenced by the efforts of Richard Stevens, who has passed on. Rich's
wisdom and talent made the specification what it is today. The co-
authors will long think of Richard with great respect.
Thanks to the many people who made suggestions and provided feedback to
this document, including: Werner Almesberger, Ran Atkinson, Fred Baker,
Dave Borman, Andrew Cherenson, Alex Conta, Alan Cox, Steve Deering,
Richard Draves, Francis Dupont, Robert Elz, Brian Haberman, Jun-ichiro
itojun Hagino, Marc Hasson, Tom Herbert, Bob Hinden, Wan-Yen Hsu,
Christian Huitema, Koji Imada, Markus Jork, Ron Lee, Alan Lloyd, Charles
Lynn, Dan McDonald, Dave Mitton, Thomas Narten, Josh Osborne, Craig
Partridge, Jean-Luc Richier, Bill Sommerfield, Erik Scoredos, Keith
Sklower, JINMEI Tatuya, Dave Thaler, Matt Thomas, Harvey Thompson, Dean
D. Throop, Karen Tracey, Glenn Trewitt, Paul Vixie, David Waitzman, Carl
Williams, Kazu Yamamoto, Vlad Yasevich, Stig Venaas, and Brian Zill
The getaddrinfo() and getnameinfo() functions are taken from an earlier
Internet Draft by Keith Sklower. As noted in that draft, William Durst,
Steven Wise, Michael Karels, and Eric Allman provided many useful
discussions on the subject of protocol-independent name-to-address
translation, and reviewed early versions of Keith Sklower's original
proposal. Eric Allman implemented the first prototype of getaddrinfo().
The observation that specifying the pair of name and service would
suffice for connecting to a service independent of protocol details was
made by Marshall Rose in a proposal to X/Open for a "Uniform Network
Interface".
Craig Metz, Jack McCann, Erik Nordmark, Tim Hartrick, and Mukesh Kacker
made many contributions to this document. Ramesh Govindan made a number
of contributions and co-authored an earlier version of this memo.
References
[1] S. Deering, R. Hinden, "Internet Protocol, Version 6 (IPv6)
Specification", RFC 2460 Draft Standard.
[2] R. Hinden, S. Deering, "IP Version 6 Addressing Architecture",
RFC 2373, July 1998 Draft Standard.
[3] IEEE Std. 1003.1-200x (Portable Operating System Interface (POSIX))
DRAFT 6, July 2000.
[4] W. Stevens, M. Thomas, "Advanced Sockets API for IPv6",
RFC 2292, February 1998.
[5] T. Jinmei, A. Onoe, "An Extension of Format for IPv6 Scoped
Addresses", Work-in-Progress.
[6] S. Deering, B. Haberman, B. Zill "IP Version 6 Scoped Address
Architecture", Work-in-Progress.
[7] B. Haberman " Routing of Scoped Addresses in the Internet Protocol
Version 6 (IPv6)", Work-in-Progress.
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 30]
INTERNET-DRAFT draft-ietf-ipngwg-rfc2553bis-03.txt February 2001
[8] E. Nordmark "Stateless IP/ICMP Translation Algorithm (SIIT)"
RFC 2765, February 2000.
Authors' Addresses
Bob Gilligan
Cacheflow, Inc.
650 Almanor Ave..
Sunnyvale, CA 94086
Telephone: 408-220-2084 (voice)
408-220-2250 (fax)
Email: gilligan@cacheflow.com
Susan Thomson
Cisco Systems
499 Thornall Street, 8th floor
Edison, NJ 08837
Telephone: 732-635-3086
Email: sethomso@cisco.com
Jim Bound
Nokia Networks
5 Wayside Road
Burlington, MA 01803
Phone: +1 781 492 6013
Email: Jim.Bound@nokia.com
draft-ietf-ipngwg-2553bis-03.txt Expires July 2001 [Page 31]
View Git Blame Copy Permalink