The fstrm_capture utility is started in the background during the
"dnstap" system test. Consequently, "rndc dnstap-reopen" and similar
commands may be executed before fstrm_capture starts listening on the
Unix domain socket it is configured to receive dnstap data on. This
results in the dnstap data sent to that socket in the meantime to be
lost; while the fstrm writer thread is able to recover from such a
scenario within a couple of seconds (by reopening the configured dnstap
destination itself), only one write attempt is made for data
successfully queued to the writer thread, so dnstap frames can still be
lost in the process. This may happen during the "dnstap" system test,
leading to the dnstap output file being empty, which in turn causes the
test to fail.
Fix by waiting until fstrm_capture starts listening on the Unix domain
socket it is configured to use before asking named to reopen the
configured dnstap destination. Since various fstrm_capture versions log
different messages when the listening socket is set up, wait for a
common string that works for all fstrm_capture versions released to
date. Add a few extra debug messages indicating test progress and make
the test fail if the expected fstrm_capture log message is not generated
within 10 seconds.
(cherry picked from commit 26d3d97f12)
The fstrm_capture.out file is overwritten when the fstrm_capture utility
is restarted during the "dnstap" system test. Use a separate output
file for each fstrm_capture instance to ensure all output produced by
that tool during the "dnstap" system test is preserved for forensic
purposes.
(cherry picked from commit bd2941fc72)
Previously, the first check silently failed, as 450 is apparently (in
the CI) the minimum output size for the dnstap output, rather than
470 which the test was expecting. Effectively, the check served as a 5
second sleep rather than waiting for the proper file size.
Additionally, check the expected file sizes and fail if expectations
aren't met.
(manually picked from commit 5f809e50b6)
On main, the minimum file size seems to 454 bytes, while on some
platforms in our CI setup for the 9.16 branch, it appears to be 450
instead.
The dnstap system test fails intermittently, and it appears to be
a timing issue - adding a short delay after running 'fstrm_capture',
and before running 'dnstap -reopen' improves the situation from
50% failures (5 out of 10 times) to 0% failures (0 out of 20 times),
tested locally.
The reason is that 'fstrm_capture' is executed in the background,
and due to OS scheduling and other factors, the listener socket
may not be ready when the following command runs and tells 'named'
to (re)open it.
(cherry picked from commit fa686fcea5)
The system test should never attempt to start or stop any other server
than those that belong to that system test. Therefore, it is not
necessary to specify the system test name in function calls.
Additionally, this makes it possible to run the test inside a
differently named directory, as its name is automatically detected with
the $SYSTESTDIR variable. This enables running the system tests inside a
temporary directory.
Direct use of stop.pl was replaced with a more systematic approach to
use stop_servers helper function.
(cherry picked from commit c100308b7d)
This commit converts the license handling to adhere to the REUSE
specification. It specifically:
1. Adds used licnses to LICENSES/ directory
2. Add "isc" template for adding the copyright boilerplate
3. Changes all source files to include copyright and SPDX license
header, this includes all the C sources, documentation, zone files,
configuration files. There are notes in the doc/dev/copyrights file
on how to add correct headers to the new files.
4. Handle the rest that can't be modified via .reuse/dep5 file. The
binary (or otherwise unmodifiable) files could have license places
next to them in <foo>.license file, but this would lead to cluttered
repository and most of the files handled in the .reuse/dep5 file are
system test files.
(cherry picked from commit 58bd26b6cf)
this changes most visble uses of master/slave terminology in tests.sh
and most uses of 'type master' or 'type slave' in named.conf files.
files in the checkconf test were not updated in order to confirm that
the old syntax still works. rpzrecurse was also left mostly unchanged
to avoid interference with DNSRPS.
(cherry picked from commit e43b3c1fa1)
This commit ensures that dnstap output files captured
by fstrm_capture are properly flushed before any attempt
on reading them with dnstap-read is done.
By reading fstrm-capture source code it was noticed that
signal SIGHUP is used to flush the capture file.
In order to lower the amount of memory allocated at startup by named
instances used in the BIND system test suite, set the default value of
"max-cache-size" for these to 2 megabytes. The purpose of this change
is to prevent named instances (or even entire virtual machines) from
getting killed by the operating system on the test host due to excessive
memory use.
Remove all "max-cache-size" statements from named configuration files
used in system tests ("checkconf" notwithstanding) to prevent confusion
as the "-T maxcachesize=..." command line option takes precedence over
configuration files.
(cherry picked from commit dad6572093)
Make yaml.load_all() use yaml.SafeLoader to address a warning currently
emitted when bin/tests/system/dnstap/ydump.py is run:
ydump.py:28: YAMLLoadWarning: calling yaml.load_all() without Loader=... is deprecated, as the default Loader is unsafe. Please read https://msg.pyyaml.org/load for full details.
for l in yaml.load_all(f.stdout):
The introduction of netmgr doubled the number of threads from which
dnstap data may be logged: previously, it could only happen from within
taskmgr worker threads; with netmgr, it can happen both from taskmgr
worker threads and from network threads. Since the argument passed to
fstrm_iothr_options_set_num_input_queues() was not updated to reflect
this change, some calls to fstrm_iothr_get_input_queue() can now return
NULL, effectively preventing some dnstap data from being logged.
Whether this bug is triggered or not depends on thread scheduling order
and packet distribution between network threads, but will almost
certainly be triggered on any recursive resolver sooner or later. Fix
by requesting the correct number of dnstap input queues to be allocated.
(cherry picked from commit 77dc091855)
The first step in all existing setup.sh scripts is to call clean.sh. To
reduce code duplication and ensure all system tests added in the future
behave consistently with existing ones, invoke clean.sh from run.sh
before calling setup.sh.
When printing a packet, dnstap-read checks whether its text form takes
up more than the 2048 bytes allocated for the output buffer by default.
If that is the case, the output buffer is automatically expanded, but
the truncated output is left in the buffer, resulting in malformed data
being printed. Clear the output buffer before expanding it to prevent
this issue from occurring.
- all tests with "recursion yes" now also specify "dnssec-validation yes",
and all tests with "recursion no" also specify "dnssec-validation no".
this must be maintained in all new tests, or else validation will fail
when we use local root zones for testing.
- clean.sh has been modified where necessary to remove managed-keys.bind
and viewname.mkeys files.
- add CHANGES note
- update copyrights and license headers
- add -j to the make commands in .gitlab-ci.yml to take
advantage of parallelization in the gitlab CI process
4669. [func] Iterative query logic in resolver.c has been
refactored into smaller functions and commented,
for improved readability, maintainability and
testability. [RT #45362]
4579. [func] Logging channels and dnstap output files can now
be configured with a "suffix" option, set to
either "increment" or "timestamp", indicating
whether to use incrementing numbers or timestamps
as the file suffix when rolling over a log file.
[RT #42838]
4572. [func] The "dnstap-output" option can now take "size" and
"versions" parameters to indicate the maximum size
a dnstap log file can grow before rolling to a new
file, and how many old files to retain. [RT #44502]